Description :

-The SparkFun Artemis Development Kit includes the SparkFun Artemis DK board, Himax camera, and USB-C cable
-Recommended software for programming: Arduino IDE, Arm Mbed OS (Studio and CLI), AmbiqSDK
-The Artemis DK acts as a Mass Storage Device (MSD), Human Interface Device (HID), and Communication Port (COM)
-Artemis Module features: Cortex-M4F with BLE 5.0 running at 48MHz with 96MHz turbo mode, low power consumption (less than 5mW), 1M flash and 384k RAM
-Arduino core allows programming the Artemis module just like an Uno or any other Arduino
-Capable of running RTOS such as Arm Mbed OS or AmbiqSDK
-Additional features: LIS2DH12TR MEMS accelerometer, digital MEMS microphone, Himax CMOS imaging camera, compatible with TensorFlow and machine learning
-Pins broken out to 0.1" spaced female headers, two rows of breakout pins with 0.1" pitch spacing, 0.08" pitch spacing for IC-hooks
-Silk on back of Artemis DK shows pins by functionality and acts as an aid while developing software
-Powered and programmed via USB-C, includes a Qwiic connector for I2C communication, fully compatible with SparkFun's Arduino core, programmable under the Arduino IDE.
- The kit includes:
1x Artemis Development Kit (Board)
1x Himax HM01B0 Camera
1x Reversible USB A to C - 0.8m

-Specifications:

1-Artemis Dev Kit:
•Compatible with Arduino, Mbed OS, and AmbiqSDK Development Programs
•Power:
5V Provided Through the USB-C Connector
1.8V, 3.3V, and 5V Available on Power Header
•Interface Chip (MKL26Z128VFM4 ARM Cortex-M0 MCU):
Drag and Drop Programming
SWD Interface
JTAG Programming PTH
•Artemis Module:
Apollo3 ARM Cortex-M4F MCU
BLE 5.0 with FCC Certification
24 Breakout I/O Pins
○ Eight 14-bit ADC Pins
○ Eighteen 16-bit PWM Pins
○ Two Independent UART Ports
○ Three Peripheral I2C/SPI Buses
JTAG Programming PTH
•Sensors:
3-axis Accelerometer (LIS2DH12)
PDM Microphone (SPH0641LM4H-1)
Camera Connector (for the Himax HM01B0 Camera)
•Qwiic Connector
On Primary I2C Bus
2.Himax HM01B0 Camera
3.Image Sensor
•Ultra Low Power Image Sensor (ULPIS) designed for Always On vision devices and applications
•High sensitivity 3.6µ BrightSenseTM pixel technology
•320 x 320 active pixel resolution with support for QVGA window, vertical flip and horizontal mirror readout
•Programmable black level calibration target, frame size, frame rate, exposure, analog gain (up to 8x) and digital gain (up to 4x)
•Automatic exposure and gain control loop with support for 50 / 60Hz flicker avoidance
•Flexible 1bit, 4bit and 8bit video data interface with video frame and line sync
•Motion Detection circuit with programmable ROI and detection threshold with digital output to serve as an interrupt
•On-chip self oscillator
•I2C 2-wire serial interface for register access
•High CRA for low profile module design
4.Sensor Parameters
•Active Pixel Array 320 x 320
•Pixel Size 3.6 µm x 3.6 µm
•Full Image Area 1152 µm x 1152 µm
•Diagonal (Optical Format) 1.63 mm (1/11″)
•Color Filter Array Monochrome and Bayer
•Scan Mode: Progressive
•Shutter Type: Electronic Rolling Shutter
•Frame Rate MAX 51 fps @ 320 x 320, 60 fps @ 320 x 240 (QVGA)
•CRA (maximum) 30º
5.Sensor Specifications
•Supply Voltage: Analog - 2.8 V, Digital - 1.5V (Internal LDO: 1.5V – 2.8V), I/O - 1.5 – 2.8V
•Input Reference Clock: 3 – 50 MHz
•Serial Interface (I2C): 2-wire, 400 KHz max.
•Video Data Interface: 1b, 4b, 8b with frame / line SYNC
•Output Clock Rate MAX: 50 MHz for 1bit, 12.5 MHz for 4bit, 6.25 MHz for 8bit
•Est. Power Consumption (include IO with 5pF load):
○ QVGA 60FPS (Typical) <4 mW
○ QVGA 30FPS (Typical) <2 mW